SMH120R46E6.7W23三螺桿泵、SMH系列臥式螺桿泵組

點火燃油泵的安全使用及維護

Ignition of safe use and maintenance of the fuel pump

1、安裝漏電保護器

1, the installation of leakage protector

漏電保護器也叫保命器，它的作用從“保命器”這三個字就可以理解。因為點火燃油泵在油下工作，容易漏電造成電能損失甚至引發觸電事故。如果裝有漏電保護器，只要點火燃油泵漏電值超過漏電保護器的動作電流值（一般不超過30毫安），漏電保護器就會切斷點火燃油泵的電源，避免漏電浪費電能，確保安全。

Leakage protector, also known as life insurance, it can be understood from the "this three word life insurance".Because the ignition fuel pump in oil, easy to leakage caused by power loss or even lead to electric shock. If there is a leakage protector, as long as the ignition fuel pump leakage exceeds the action leakage protection current value （generally not more than 30 MA）, electric leakage protection device will cut off the ignition of the fuel pumppower, to avoid wasting electricity leakage, to ensure safety.   

2、電源電壓異常莫開機

2, Mo power supply voltage abnormality

農村由于低壓供電線路比較長，線路的末端電壓過低是常有的事。當相電壓低于198伏，線電壓低于342伏時，點火燃油泵電機轉速下降，當達不到額定轉速的70%時，啟動離心開關會閉合，造成啟動繞組長時間通電而發熱甚至燒壞繞組和電容器。相反，電壓過高引起電機過熱而燒壞繞組。因此，點火燃油泵在作業中，操作者必須隨時觀察電源電壓值，若低于額定電壓10%以下，高于額定電壓10%以上，應使電機停止運轉，找出原因并排除故障。

Low-voltage power lines in rural areas as long, terminal voltage is low line is constant some thing. When the phase voltage below 198 volts, the line voltage is lower than 342 volts, the ignition fuel pump motor speed down,when up to 70% less than the rated speed, the centrifugal start switch closed, resulting in start winding electricityand heat and even burn winding and capacitor. On the contrary, caused by high voltage motor overheating and burn winding. Therefore, the ignition of fuel pump in operation, the operator must always observe the power supply voltage value, if less than the rated voltage below 10%, higher than the rated voltage above 10%, should the motor stop running, find out the reasons and troubleshooting.  

3、莫讓點火燃油泵*超負荷工作

3, do not let the ignition fuel pump overload

為避免潛油電泵*超負荷工作，不要抽含沙量大的油并隨時觀察電流值是否在銘牌上規定的數值，若發現電流過大，應停機檢查。另外，電泵脫油運行的時間不宜過長，以免使電機過熱而燒毀。

In order to avoid the electric submersible pump long-term overload of work, numerical do not draw large sedimentoil and observe whether the current value specified on the nameplate, if too much current is found, should be down to check. In addition, the electric pump oil removing operation time should not be too long, to avoid overheating and burning motor.

4、避免頻繁開關

4, to avoid frequent switching

不要頻繁地開關點火燃油泵，這是因為電泵停轉時會產生回流，若立即開機，會使電機負載啟動，導致啟動電流過大而燒壞繞組。由于啟動時電流很大，頻繁啟動也會燒壞點火燃油泵電動機繞組。

The ignition of fuel pump do not frequently switch, this is because the pump will stop to have a return, if an immediate start, will start the motor load, resulting in excessive starting current and burn winding. As the start when the current large, frequent starts will burn the fuel pump motor ignition winding.

Insulation resistance

5、電纜線安裝與潛油電泵的絕緣電阻要求

5, cable installation and electric submersible pump

安裝點火燃油泵時，電纜線要架空，電源線不要太長。點火燃油泵下油或提出時切勿使電纜受力，以免引起電源線斷裂。點火燃油泵工作時不要沉入泥中，否則會導致電機散熱不良而燒壞電機繞組。安裝時，電機的絕緣電阻不應低于0.5兆歐。

Install ignition fuel pump, to the overhead cable, power line should not be too long. Ignition fuel pump oil or propose not to force the cable, so as not to cause a power line fault. Ignition fuel pump work do not sink into the mud, or would result in poor motor cooling motor windings burned. When in installation, insulation resistanceshould not be less than 500000000000 ohm motor.

6、電機的旋轉方向要正確

The direction of rotation, the motor 6 to the right

應搞清電機的旋轉方向，現在有許多類型的點火燃油泵正轉和反轉時皆可出油，但反轉時出油量小、電流大，其反轉時間長了會損壞電機繞組。

We should understand the direction of motor rotation, there are many types of ignition of fuel pump when the forward and reverse can be out of oil, but the reverse when the oil quantity is small, current, its reversal long time may damage the motor windings.

7、勤查勤看發現問題及時修復

7, Qin Chaqin see repair problems in a timely manner

平時要經常檢查電機，如發現下蓋有裂紋、橡膠密封環損壞或失效等，應及時更換或修復，避免油滲入點火燃油泵。

Usually should always check the motor, such as a crack was found under the lid, rubber seal ring damage or failure, should be timely replacement or repair, oil into the ignition fuel pump to avoid.

SM三螺桿泵：SMH三螺桿泵、SMS三螺桿泵、SMF三螺桿泵、SME三螺桿泵、SMGH三螺桿泵     黃山天曼供應高壓立式三螺桿泵電機組    供應高壓三螺桿泵/SM三螺桿泵，SMH三螺桿泵

SM three screw pump: SMH three screw pump, screw pump, SMS three SMF three SME three screw pump, screw pump, SMGH three screw pump making Mount Huangshan teamon supply high pressure vertical three screw pumpturbine making supply voltage of three screw pump /SM three screw pump, SMH three screw pump     

一、SM系列三螺桿泵的歷史：A, SM series three screw pump history
三螺桿泵問世比較晚，1930年法國工程師雷涅-摩伊諾（也譯為莫諾）創造*臺單螺桿泵，1931年瑞典IMO公司發明三螺桿泵。1943年，德國鮑曼公司生產外置軸承的雙螺桿泵，從1944年開始批量省事，1959年以來，德國費里茨一基伯格對單螺桿泵作了重大改進，他設計和制造了德國*臺新型單螺桿泵。截止1972年，市場上所有的螺桿泵轉子和定子的幾何形狀還都是1935年研制的。

three screw pump appeared relatively late, the French engineers in 1930Leinie - milf Connaught （also translated as Monod） to create the first single screw pump, in 1931 the Swedishcompany IMO has three screw pump. In 1943, double screw pumpGerman Bauman company external bearing,from the beginning of 1944 batch save trouble, since 1959, the German Feilici Jiboge on a single screw pump has made significant improvements, he designed and manufactured the first German new single screw pump. As of 1972, the market all the screw pump rotor and stator geometry are also developed in 1935.

我國螺桿泵的發展起步比較晚，原天津市工業泵廠于20世紀60年代初期研制成功船用高壓小流量三螺桿泵，此后逐步發展成為單、雙、三螺桿泵的專業生產。60年代中期，原沈陽水泵廠開始生產雙螺桿泵和三螺桿泵，70年代研制成功五螺桿泵。

Development in China started relatively late screw pump, the Tianjin Industrial pump factory in the early nineteen sixties developed marine high pressure and small flow three screw pump, then gradually developed into aprofessional production of single, double, three screw pump. The mid 60's, the original Shenyang water pump factory began production of double screw pump and the three screw pump, 70 in the successful development of the five screw pump.

我公司常年生產：南京SNH三螺桿泵，天津SNS立式三螺桿泵，天泵SNF法蘭式三螺桿泵，SMH高壓點火油泵，SMS高壓三螺桿泵，SMF三螺桿泵HSNH低壓循環三螺桿泵，HSNS立式三螺桿泵，HSNF液壓潤滑三螺桿泵，南京QSNH三螺桿泵，QSNF三螺桿泵，QSNS三螺桿泵，3GR低壓三螺桿泵，3GC船用三螺桿泵，3GS雙吸三螺桿泵，3GCL船用立式三螺桿泵，SPF燃油噴射泵，南京3G三螺桿泵，HSM三螺桿泵，HSJ油浸式三螺桿泵，HSG三螺桿泵，德國allweiler三螺桿泵，瑞典IMO三螺桿泵，美國imo AB三螺桿泵，KRAL三螺桿泵，seim三螺桿泵，德國Leistritz三螺桿泵等等；

My company perennial production: Nanjing SNH three screw pump, Tianjin SNS vertical three screw pump pump,day SNF flange type three screw pump, SMH high voltage ignition oil pump, SMS pressure three screw pump,screw pump SMF three HSNH low pressure cycling three screw pump, HSNS vertical three screw pump, hydraulicoil HSNF three screw pump, Nanjing QSNH three screw pump, screw pump, QSNF three, QSNS three screw pump,low voltage 3GR three screw pump, three screw pump of 3GC ship, 3GS double suction three screw pump, vertical three screw pump 3GCL ship, SPF fuel injection pump, Nanjing 3G three screw pump, HSM three screw pump, HSJoil immersed type three screw pump, HSG three screw pump, the German allweiler three screw pump, the SwedishIMO three screw pump, the United States IMO AB three screw pump, screw pump, KRAL three, seim three screw pump, the German Leistritz three screw pump etc.;

歡迎廣大新老客戶、訂貨，垂詢：

SMH三螺桿泵主要應用：

SMH three screw pump is mainly used:  
高壓蒸汽鍋爐燃油輸送； 

High pressure steam boiler fuel delivery;
船舶工業，柴油發動機，渦輪鍋爐等；

Shipbuilding industry, diesel engine, turbine boiler etc.; 
燃油輸送系統應用；

Application of the fuel delivery system; 
傳送介質范圍： 

The transmission medium range:
船用柴油，汽油（MDO,MGO）,重型燃油HFO，車用燃油，生物油等 

Marine diesel, gasoline （MDO, MGO） HFO, heavy fuel, vehicle fuel, bio oil
產品說明： 

Product deion:
可以提供電機+螺桿泵組裝成套供貨，附帶吸油管道和支架等，以及完整的測試報告；

Can provide motor and screw pump assembly and delivery, incidental suction pipe and the support, and a complete test report;
可以提供壓力安全閥組等配套附件；

Can provide pressure relief valve group and other accessories; 
可選擇徑向或軸向吸油口，SAE法蘭BSPP或螺紋連接； 

Can choose the radial or axial suction port of SAE BSPP or threaded connection, flange;
螺桿泵體表面特殊處理，硬度為63HRC；重載機械密封， 

Screw pump with special surface treatment, hardness is 63HRC; heavy duty mechanical seal,
螺桿泵外部護套（可選）材質為AMSE標準，可根據API標準制造； 

Screw pump outer sheath （optional） made of AMSE standards, can be manufactured according to API standard;
螺桿硬度為63HRC，超精密加工；

Screw the hardness is 63HRC, ultra precision machining; 
介質的zui低允許黏度為2cst，zui高1000cst,允許zui大顆粒物30um.

Medium viscosity minimum allowed is 2cst, maximum 1000cst, maximum 30um. particles 
螺桿泵zui高壓力達8MPa; 

The highest pressure screw pump up to 8MPa;
流量范圍:0-2000L/min 

Flow range: 0-2000L/min

SMH三螺桿泵簡介Introduction to SMH three screw pump

一、特點 One, characteristic

SM三螺桿泵 SM three screw pump

1.SMH高壓三螺桿泵是利用轉子液壓平衡技術，所以在工作時候振動小，噪音低。

1.SMH high voltage three screw pump is the use of hydraulic balancing rotor, so the work when small vibration, low noise

2.SMH輸出穩定，工作時無脈動。

2.SMH output stability, work without pulsation.

3.SMH點火油泵的工作效率高。

3.SMH ignition oil pump with high efficiency.

4.SMH三螺桿泵具有很強的自吸能力。

4.SMH three screw pump has a strong self absorption capacity.

5.SMH燃油輸送泵結構簡單具有很強的互換性，還能根據使用現場的條件，安裝成SMH臥式安裝三螺桿泵，SMF支架式安裝三螺桿泵，SMS立式安裝三螺桿泵，如有特殊要求還可以訂做。

5.SMH fuel pump has the advantages of simple structure, a strong interchangeability, can according to the siteconditions, installation of an SMH SMF three screw pump horizontal installation, scaffolding installation of three screw pump, SMS vertical installation of three screw pump, if there are special requirements can also becustomized.

6.SMH熱電廠用點火油泵具有結構緊湊，體積小，重量輕，可在較高轉速下工作。

6.SMH power plant ignition oil pump has the advantages of compact structure, small volume, light weight, can be in high speed.

歡迎廣大新老客戶、訂貨，垂詢：

公 司 名稱：

黃山天曼泵業有限公司

姓名：

程曉 （銷售 ） （）

辦 公 地址：

中國 黃山市徽州區城北工業園 

郵      編：

245400

電      話：

86-

傳      真：

86-

移 動 ：

郵      箱：

Hstmby01

：

阿 里 旺旺:

旺旺：hstmby01

公司主頁：

http;//www.hstmby.comhttp://www.luogb.com  http://www.cntmby.comhttp://www.tm-p.cc 

Company name: Mount Huangshan teamon pump industry limited company

Contact person: Mr. Cheng Xiao （Sales Manager） （）

Office address: China Huangshan City Huizhou area north of the City Industrial Park

Postal Code: 245400

86-

86-

phone:

: Hstmby01

: :

A: I want to: hstmby01

Company homepage: http; //www.hstmby.comhttp://www.luogb.com

                                http://www.cntmby.comhttp://www.tm-p.cc