上海榮計達儀器科技有限公司**經營水泥實驗儀器、混凝土實驗儀器、公路土工實驗儀器、干粉砂漿保溫砂漿實驗儀器、瀝青防水材料實驗儀器、油漆涂料實驗儀器、無損檢測等實驗儀器。**經營水泥實驗儀器、混凝土實驗儀器、公路土工實驗儀器、干粉砂漿保溫砂漿實驗儀器、瀝青防水材料實驗儀器、油漆涂料實驗儀器、無損檢測等實驗儀器。公司產品憑借過硬的質量、完善的售后服務、合理的價格各大院校、檢測單位、建材企業、工程建設單位。在消費者當中享有較高的地位和良好的口碑，用戶遍布國內近三十個省市、自治區，并遠銷國外，與用戶建立了長期穩定的合作關系。公司實力雄厚，重信用、守合同。有健全的管理制度和完善健全的質量管理體系。并有反應迅速、服務周到的售后服務系統。我們將不懈努力、一如既往以優異的品質為客戶服務。
Shanghai Rongjida Instrument Technology Co., Ltd. ** operates cement experiment equipment, concrete experiment equipment, highway geotechnical experiment equipment, dry mortar thermal insulation mortar experiment equipment, asphalt waterproof material experiment equipment, paint coating experiment equipment, non-destructive testing and other experimental equipment. ** Operating cement experiment equipment, concrete experiment equipment, highway geotechnical experiment equipment, dry mortar thermal insulation mortar experiment equipment, asphalt waterproof material experiment equipment, paint coating experiment equipment, non-destructive testing and other experimental equipment. Company products rely on excellent quality, perfect after-sales service, reasonable prices sell well in major universities, testing units, building materials enterprises, engineering construction units. It enjoys a high status and a good reputation among consumers, and has customers in nearly 30 provinces, cities, and autonomous regions in China, and has been exported to foreign countries. It has established long-term and stable cooperative relationships with users. The strength of the company, credit and contract compliance. Have a sound management system and a sound quality management system. And has a responsive and thoughtful after-sales service system. We will make unremitting efforts to serve our customers with excellent quality as always.
防水涂料涂膜模具符合GB/T16777-2008，GB/T19250-2003標準， 本涂膜模框是建筑防水材料（聚氨酯類、聚丙烯酸酯類）拉伸性能系列試驗，制備試樣用的涂膜模具。用此涂膜模具能制出350mm320mm*1.5mm的試樣膜，然后用切片機切割涂膜可制得符合GB/T528標準規定的啞鈴狀Ⅰ型試樣，以備不同拉伸試驗之用。
The coating film frame conforms to GB / T16777-2008 and GB / T19250-2003 standards. This coating film frame is a series of tests for tensile properties of building waterproofing materials (polyurethanes, polyacrylates), and a coating film mold for preparing samples. . Using this coating film mold, a sample film of 350mm320mm * 1.5mm can be made, and then the coating film can be cut with a microtome to obtain a dumbbell-shaped type I sample that meets the requirements of the GB / T528 standard for different tensile tests.
防水涂料涂膜模具技術參數：
★結構：本涂膜模具由模框、涂刮棒、基板及底座組成.
★尺寸規格：外框尺寸410mm*380mm*1.5mm
★內框尺寸350mm*320mm*1.5mm
★涂膜厚度 （1.50.2）mm：
Coating film frame technical parameters:
★ Structure: The coating film mold consists of a mold frame, a coating bar, a substrate and a base.
★ Dimensions: 410mm * 380mm * 1.5mm
★ Inner frame size 350mm * 320mm * 1.5mm
★ Coating film thickness (1.50.2) mm:
防水涂料涂膜模具使用方法：
★在試樣制備前，所取樣品及所用儀器均在標準條件下（溫度23℃±2℃；相對濕度45％~70％） 放置24h。
★為了便于脫模，在基板（玻璃板）上和模框上可用硅油或石蠟作脫模劑進行表面處理。
★在標準條件下，將靜置后的樣品攪拌均勻，若樣品是雙組分涂料，則按產品的配合比稱取所需的主劑和固化劑，把兩組分混合后充分攪拌5min。
★在不混入氣泡的情況下將攪拌好的防水涂料立即傾倒于本涂膜模具中進行涂覆。
★樣品應分次涂覆，A后一次用涂刮棒將其表面刮平，并在標準條件下養護168h。
★檢查涂膜外觀，表面應無明顯氣泡、光滑且平整。
★起膜后，用切片機切割涂膜，制得符合GB/T 528所規定的啞鈴狀Ⅰ型試樣，以備不同拉伸試驗之用。
How to use the coating mold frame:
★ Before the preparation of the samples, the samples taken and the instruments used were placed under standard conditions (temperature 23 ° C ± 2 ° C; relative humidity 45% ~ 70%) for 24 hours.
★ In order to facilitate demolding, silicone oil or paraffin can be used as a mold release agent on the substrate (glass plate) and mold frame for surface treatment.
★ Under standard conditions, stir the sample after standing evenly. If the sample is a two-component coating, weigh the required main agent and curing agent according to the product mix ratio, and mix the two components for 5 minutes.
★ Pour the stirred waterproof paint into this coating film mold for coating immediately without mixing air bubbles.
★ The sample should be coated in several steps. After A, the surface should be scraped flat with a coating bar and cured under standard conditions for 168h.
★ Check the appearance of the coating film. The surface should be free of obvious bubbles, smooth and flat.
★ After filming, use a microtome to cut the coating film to obtain dumbbell-shaped type I specimens that meet the requirements of GB / T 528 for different tensile tests.
