粉碎設備 混合設備 分離設備 濃縮結晶設備 傳質設備 干燥設備 反應設備 換熱設備 制冷設備 空分設備 儲存設備 鍋爐|加熱設備 包裝機械 輸送設備 化工實驗室設備
無錫怡遠鋼管有限公司
無錫怡遠鋼管有限公司
異型鋼管是經冷拔制成各種異型的無縫鋼管
異型鋼管是經冷拔制成各種異型的無縫鋼管。異型鋼管一般是根據斷截面來區分的，按材料來說又可分為無縫異型鋼管，鋁合金異型管，塑料異型管。不銹鋼異型管焊接時，應該注意事項：焊接6mm以下薄板的異型管時，要具備焊縫成型美觀，焊接變形量小的特點。鎢極從氣體噴嘴突出的長度，以4-5mm為佳，在角焊等遮蔽性差的地方是2-3mm，在開槽深的地方是5-6mm，噴嘴至異型管的距離一般不超過5mm。焊接電弧的長度，焊接普通鋼時以2-4mm為佳，而焊接不銹鋼異型管時以1-3mm為佳，過長則保護效果不好。
Special-shaped pipe is made of various special-shaped seamless steel pipe by cold drawing. Special-shaped pipe is generally distinguished according to the broken section. According to material, it can be divided into seamless steel pipe special-shaped pipe, aluminum alloy special-shaped pipe, plastic special-shaped pipe. When welding stainless steel special-shaped pipe, we should pay attention to the following points: when welding the special-shaped pipe with thin plate under 6mm, it should have the characteristics of beautiful weld shape and small welding deformation. The length of tungsten pole protruding from gas nozzle is 4-5mm, 2-3mm in places with poor shielding ability such as fillet welding, 5-6mm in places with deep groove, and the distance from nozzle to special-shaped pipe is generally not more than 5mm. The length of welding arc is 2-4 mm for ordinary steel, 1-3 mm for stainless steel special-shaped pipe, and too long is not good for protection.
為使氬氣很好地保護焊接熔池，和便于施焊操作，鎢極中心線與焊接處工件一般應保持80-85°角，填充焊絲與管材表面夾角應盡可能地小，一般為0°左右。焊接異型管時，采用垂直特性的電源，直流時采用正極性。保護氣體為氬氣，純度為99.99%。當焊接電流為50-50A時，氬氣流量為8-0L/min，當電流為50-250A時，氬氣流量為2-5L/min。有風的地方，務請采取擋網的措施，而在室內則應采取適當的換氣措施。為防止焊接氣孔之出現，焊接的異型管部位如有鐵銹、油污等務必要先清理干凈。對接打底時，為防止異型管底層焊道的背面被氧化，背面也需要實施氣體保護。
In order to protect the weld pool well by argon gas and facilitate welding operation, the tungsten pole center line and the workpiece at the welding site should generally maintain an angle of 80-85 degrees, and the angle between the filler wire and the surface of the pipe should be as small as possible, generally about 0 degrees. Vertical power supply and positive polarity are used in welding special-shaped pipe. The protective gas is argon with a purity of 99.99%. When welding current is 50-50A, the argon flow rate is 8-0L/min, and when welding current is 50-250A, the argon flow rate is 2-5L/min. In windy areas, please take measures to block the net, while indoors should take appropriate ventilation measures. In order to prevent the occurrence of welding blowhole, it is necessary to clean the irregular welded pipe if there is rust and oil stain. In order to prevent oxidation on the back of the bottom weld of the special-shaped pipe, gas protection is also needed on the back of the weld.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
化工機械設備網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
